Saim Marine presents the V-shaped interceptors manufactured by the Swedish Zipwake – www.zipwake.com . They make the successful Series S even more versatile and highly competitive. V-shaped interceptors for centerline mounting are perfect for filling the gap between twin outboards or stern drives, as well as dual propeller tunnels and pods. The four V-shaped models cover deadrise angles effectively between 11 to 24 degrees. V-shaped centerline mounted interceptors can be included in new installations, or retro-fitted to already installed systems. In combination with Zipwake straight interceptors, or alternatively mounted as a single unit, the V-shaped interceptors further increases flexibility of installation and application in boats with different hull design and engine options. The V-shaped interceptors for centerline mounting contribute to achieve a near full beam interceptor arrangement for optimal lift efficiency, inherently requiring a small blade stroke of just 30 mm. In addition, interceptor actuation is in general significantly faster than conventional trim tabs and the use of interceptors hence enables to rapidly respond to external forces acting on the boat, to maintain the boats desired pitch and roll angles for better performance, fuel economy, comfort and safety.
Ancona, 2017 July, 31st – It has been a complete success the commissioning start-up procedure of the eTRAC stabilization system which took place on board of the new ISA Yacht 37m located at the shipyard in Ancona.
The system has eTRAC 300 actuators with 1,6sqm fins and it’s suitable both for underway and for at anchor stabilization. Pretty easy to install by the shipyard, after the check of connection made by ABT-TRAC engineers, the sea trials and system settings have been made in a few hours.
The new eTRAC product range will soon see the official launch of the eTRAC 250 actuators, developed for fins starting from 0,4sqm and covering the needs of smaller yachts. The new eTRAC 250 will be displayed at Cannes and Genoa boat shows next September on SAIM Marine booths.
The courses regarding ZF electronic controls were held at ZF headquarters in Arco di Trento and have focused on the line Smart Command and the new JMS (Joystick Maneuvering System).
They involved more than 30 specialized technicians from 20 authorized Service Points.
The courses were held by our Service Engineer Marco Oltolina with the support of Davide Mazzotta (SAIM Network Technical Manager) and the ZF Staff.
In addition to a theoretical session, the techinical staff carried out tests in open waters, sailing on board of the ZF Test Boat on the Garda Lake.
The technical training session concerning the new range of marine generators Kohler 12 – 24kW, addressed to Saim Dealer Network – Level 1 has just ended.
The course, which was organized in two sessions from the 7th to 10th of February, involving 40 specialized technicians from 20 companies located throughout the country, has been held by Service Manager SAIM Marco Pezzuolo with the support of the Service Manager KOHLER Francesco Pitardi. The training was focused on the new gen-set range equipped with KOHLER Diesel engines.
In particular, the features of these new series have been studied in details as well as the new soundproofing cabin and the new and revolutionary DEC3500 controller that offers the possibility of parallel operation with multiple generator sets (also single phase) thanks to PGEN® system patented by KOHLER.
In Salzburg (Austria) took place the last Ferretti Group Convergence, the annual conference that brings together several commanders of the Ferretti Group yachts and shuttles.
The participants this year were over 100 and the main Sponsor of the event was the Norwegian SIDE POWER, as well as MAN and RINA.
Ronny Skauen, Side Power General Manager, held to commanders a theoretical session lasting two hours, explaining the features and benefits of the Side Power thrusters and stabilizers.
SAIM has supported the event by participating actively in the organization of this worldwide important meeting point.
A technical training exclusively addressed to Ferretti dealers was held by Ferretti Service University at Saim headquarters at Buccinasco on February 9th and 12th.
More than 40 dealers attended the event focused on Kohler ranges K and DJ. The 2-day program included sessions concerning the new EFKOZD and EFOZDJ with Kohler engine, theory and practical courses for the DEC3500 functionality and new FRX alternator. Attention was drawn to the use of original spare parts for maintenance and service schedules of all models were delivered to the dealers.
The meeting was a great opportunity to develop major technical issues at Saim thanks to Ferretti Service University and the technical staff of Saim Service department.
SAIM has been appointed as exclusive sales agent for Italy for Zipwake Dynamic Trim Control Systems by the Swedish company.
SAIM Group will be responsible for increasing awareness of the Swedish engineering firm’s latest developments in fast acting interceptors and kit boxes for dynamic control system, whilst driving sales in Italy.
Both SAIM and Zipwake have established enviable reputations within their respective fields for the development and distribution of high quality marine equipment. The signing of the new agreement means both parties can look forward to expanding Zipwake Dynamic Trim Control System’s market presence.
SAIM enthusiasm for collaborating with the Swedish company further demonstrates the quality and unique benefits of Zipwake interceptor.
Superyacht sailboat and motor yacht owners have long desired a robust capstan that is capable of being
retracted, when not in use, in order to provide an uncluttered deck area; whether it be located on the
foredeck or installed in the mid ship and/or stern areas of a vessel.
Maxwell has developed an inspired solution which allows for a retractable unit every bit as functional and strong as a non-retractable capstan.
The entire Maxwell Retractable Vertical Capstan (RVC) has been designed not only for superb functionality,
but with the aim that aesthetics aboard any Superyacht are also paramount.
The top of the capstan drum is pleasing to the eye and has been patterned to provide a non-skid surface when flush with the deck, in
the fully “DOWN” position.
Operation of the Maxwell RVC, which performs above the exacting performance criteria of the conventional
Maxwell VC4000 capstan, is as simple and straightforward as any conventional capstan.
Adjustment and maintenance of the RVC is equally simple, utilising a basic tool kit with minimal disassembly of the unit.
Underwater Lights Limited expand their already comprehensive portfolio of lights with new Marlin surface mounted lights. This surface mounted light is ideal for smaller craft with its simple non-cutting installation and simple plug and play system utilizing an integral driver.
Offering 2800 lumens of brightness, the lights give a wide 60 degree angle of beam making them ideal for super yacht tenders, pleasure boats or even fishing boats. With electrics bonded through the power cable the lights give 40,000 hours of LED life. Available in white and blue, it’s built from armor coated AB2 bronze.
Marlin Lights will be shown at the forthcoming boat shows next September at Saim Marine booth.
SEA RECOVERY APPOINTS SAIM MARINE AS NEW DISTRIBUTOR FOR ITALY
Saim Marine, the Italian Distributor of Parker-Recor since longtime, has been appointed as the new Distributor for Sea Recovery watermakers on the Italian territory. The distributorship will be effective February 1, 2015 and was announced during the Sea-Tec exhibition in Carrara.
Both Sea Recovery and Saim Marine have established enviable reputations within their respective fields for the development and distribution of high quality marine equipment. The signing of the new agreement means both parties can look forward to expanding Sea Recovery’s market presence. As Raffaele Invrea (Sales Manager for Sea Recovery) explains, “We are glad to have the opportunity to work with one of the marine industry’s most respected players in Italy. We look forward to starting our business experience with Saim Marine as we have immediately shared a vision to work with.”
Marco Donà (CEO of Saim) comments on the appointment: “Sea Recovery products are the best in water purification as far as quality, technology and reliability are concerned. Saim is thus completing its product range with another premium product”.
Saim Marine has been an important distributor to the marine industry for more than two decades. Since then, the company has been equipping applications ranging from recreational marine to commercial vessels and is the supplier of choice for many of the most prestigious Italian shipyards. Saim Marine distributes high quality equipment along the southern coast of Europe with operations based in Buccinasco (Milan), Fiumicino (Rome), Viareggio and Bologna in Italy, and Mandelieu in France which is run by its sister company, Saim France Sarl.
Doug Blakeman, VP of Sales for Parker-Racor, adds: “Our new range of watermakers has been designed to be integrated in a technologically advanced motor yacht. The Sea Recovery cutting-edge engineering together with the commitment to developing exciting new products help attract the top tier of shipyards and yacht owners worldwide. Saim’s experience in providing quality equipment to the marine industry is a terrific asset and we are delighted they will now be able to offer Sea Recovery watermakers to all their existing clients.”
— More About Sea Recovery —
Sea Recovery has manufactured the most innovative and intuitive watermakers for the past 30 years. By incorporating a customer-first philosophy into our designs, the quality of our products are never compromised. We believe that boaters deserve more from their watermakers. Dealing with confusing controls and maintenance should not be a concern. Our company strives to communicate to the heart of the leisure boater, by engineering systems that marries style with functionality, a formula that has made Sea Recovery the #1 watermaking brand among marine consumers and boatbuilders around the world. We offer an innovative line of watermakers that suit every need in the boating industry, from the fully automated Aqua Matic to the miniature Aqua Whisper Mini Series to the energy efficient Ultra Whisper system.
— More About Saim —
Founded in 1951, Saim soon became a reference point in the supply of automotive groups and various Italian companies in the marine and industrial applications. As the first ZF distributor in Italy, Saim has always been associated with products of the highest quality pre-service and post-sale of the first level and organization in the territory that represents to its customers a trusted partner.
Saim Marine, officially founded in 1993, selects and distributes top quality components and equipment to the most prestigious Italian shipyards. Saim Marine is built on four branches located in strategic points: Buccinasco (MI), Fiumicino (RM), Bologna, and Mandelieu on the French Riviera.
Through the network of sales and service distributed on all the Italian, French, and Croatian coasts, Saim Marine accompanies its direct customers (shipyards) and end users (yacht owners) from the choice of correct equipment to the end of a serene cruise. Last year Saim Spa has been awarded ISO 9001:2008 certification for its Quality Management System.
February 4th, 2015
Saim Marine Press Office:
Saturno e Associati Giornalisti, via Ciro Menotti, 21 – 20129 Milano –firstname.lastname@example.org -
Gabriella Cottignoli, tel +39 340 1686 130